eProcureOpenWorks
Delhi › Ministry of Railways
S&T work for Interlocking of 27 Nos Non-Interlocked LC gates having TVU >20000 and < 50000 over Firozpur Division.List of LC-Gates:- JRC-HSX Section 6 LC Gates(C-2,C-11,C-25, C-34 , C-41,C-49).JUC-FZ…
Ministry of RailwaysHQ Office , Northern Railway Baroda House New Delhi
New Delhi
Est. value ₹12 Cr · EMD ₹23.9 L · Closes 30 Oct 2026, 11:30 am
Ministry of Railways published this works tender on eProcure on 6 Oct 2026, for New Delhi. The estimated value is ₹12 Cr and the EMD is ₹23.9 L. It closes on 30 Oct 2026, 11:30 am IST. Tender ID 92467409 · Ref 02-SnT-PROJ-UMB-2026-27.
Timeline
- Published6 Oct 2026
4:04 pm - Bidding starts16 Oct 2026
- Closes30 Oct 2026
11:30 am
Key figures
Estimated value₹12 Cr
EMD₹23.9 L
Closing date30 Oct 202611:30 am IST
Key facts
- Contract type
- Works - General · Expenditure
- Tender type
- Open
- Tendering section
- SNT PROJEC
- Bidding system
- Two Packet System
- Bidding style
- Single Rate for Tender
- Validity of offer
- 90 days
- Completion period
- 12 Months
- Tender document cost
- None
- JV / consortium
- JV allowed (up to 3 members), no consortium
- Ranking order
- Lowest to Highest
- Expenditure type
- Capital (RSP)
- Pre-bid meeting
- None
- Inviting officer
- Dy. CSTE/PROJ./UMBNR HQ-S AND T/NORTHERN RLY
Complies with the Public Procurement (Make in India) Order 2017
The tender inviting authority confirms this tender does not violate the GFR rules on procurement through GeM
Bidders from a country sharing a land border with India must be registered with the competent authority
About this tender
For complete description and other details, please refer to tender
- Reference
- 02-SnT-PROJ-UMB-2026-27
- Tender ID
- 92467409
- Bid type
- Open/Advertised
- Product category
- Railway related Products
- Organisation type
- Central Govt. Ministry/Department
- Location
- New Delhi
- Portal
- eProcure
- Inviting authority
- NR HQ-S AND T/NORTHERN RLY
Schedule of work
| Item | Quantity | Railways’ estimated rate | Amount |
|---|---|---|---|
| Schedule A · Drawing & Design Items | |||
| 1Design and preparation of wiring diagram for Level-Xing MACLS on the basis of approved interlocking plan,typical circuit diagram and as per Railway practice and latest rules prescribed by the Railway and obtaining approval of the competent authority. Designing , preparation of locking table, selection table, circuit diagram,contact analysis chart, relay rack chart etc, preparation of operating & indication panel Domino type diagram, (circuit shall be designed by the contractor with the use of Q series relays on the basis of approved signal Interlocking plan and obtaining approval of Competent Authority). The operating & indication panel may have addition & alteration to an extent of 5% variation in number of Domino. Designing should be as per Railway specifications and as per latest rules prescribed by Rly. This also includes preparation of cable route plan,Cable core chart,Station working rule diagram,Power supply arrangement,Cable termination chart in relay room and location boxes,Location wiring plan,Cable insulation chart,Fuse analysis,Indoor circuit diagram,Track circuit jumper plan,Terminal and Contact analysis chart,Outdoor circuits and other outdoor diagrams and obtaining approval of the engineer as per following :-Supply of 6 copies of complete set of superior quality paper including one set laminated,properly bound in file with cushioned cover. Software backup of complete set in the form of CD (2 Nos.) One complete set of tracings Design through CAD. Drawings in A-3 size & plan in bigger size papers. (six sets). (Inspection: JE/SSE/P/D&D). | 27 LC Gate | ₹39,797.39 | ₹10,74,529.53 |
| 2Modification /Alteration/Augmentation of existing Electronic Interlocking (EI) System as per RDSO/SPN/192/2019 Ver.2.0 or latest (with latest amendment), as per approved Signaling planand selection table/locking table of stations in connection with signalling work at station of FZR division as per requirement, technical specifications & conditions of contract. This includes- 1) Design & drawing of Indoor circuit diagram. 2) Modification to the existing Application Software of VDU & MT. 3) Modification to the existing interface & Interlocking circuit for stations. 4) Alteration to the existing Relay Rack wiring as per the modified interface circuit for Stations. 5) Modification to the existing CCIP at stations. 6) Upgradation of Datalogger Data base.7) Necessary modification in existing PI/RRI Panel.8) Supply of additional EI Hardware modules/cards for doing the alteration at above mentioned stations.9) FAT and SAT as per the modified and approved Application logic. 10)Installation, wiring,programming, testing & commissioning of complete yard for data input & configuration,simulation & functional testing, diagnostic & trouble shooting and commissioning of Electronic interlocking System as per Signal Interlocking plan.Installation is to be done as per RDSO specification no. RDSO/SPN/192/2019Ver. 2.0 or latest and RDSO practice circulated vide TAN no.STS/E/TAN/3012 Ver. 2.0Dt.10.08.2016 or latest,TAN no. STS/E/TAN/3007Ver. 1.0 Dt. 02.11.2012 orlatest and TAN no.STS/E/TAN/3006, Ver.3.1, dt. 30.06.2025 orlatest for earthing and bonding scheme (as applicable) for Electronic Interlocking. (Inspection by RDSO). A) (M/s Kyosan) on JRC-HSX Section 3 LC Gates (C-25,C-41,C-49), PHR-LNX Section 1 LC Gate (C-20). B) (M/s Ansaldo) on JUC-FZR Section 1 LC Gate (C-20), BTI-FZR Section 1 LC Gate (C-33). C) (M/s Medha) on FZP-FKA Section 2 LC Gates (C-54,C-58) from same station, KKP-FKA Section 1 LC Gate (B2-32). | 8 Job | ₹34,02,557.52 | ₹2,72,20,460.16 |
| Schedule B · Supply Items | |||
| 1Design, Manufacturing & supply of electrically operated lifting barrier 110V AC as per requirement (as per RDSO spec RDSO/SPN/208/2012 ver.2.0 or latest ) complete set (A set consists of two boom and other accessories as per RDSO's latest Specifications) with boom length 9.76 Mtr (approx. 10 Mtr.)along with pedestal driving and driven mechanism, balancing weight, boom support and motorized boom locking arrangement, circuit controllers, operating panel, road warning bell, hand generator & crank handle for emergency operation with all accessories complete in all respect. (Inspection: RDSO). | 27 Set | ₹4,01,932.30 | ₹1,08,52,172.10 |
| 2Supply of PVC insulated multi strand, single core copper conductor of size 16/0.2 mm (0.5sqmm) as per IS 694:2010 and RDSO Specn.No.IRS:S- 76/89 (Amnd-3) or latest. (Inspection: Consignee). | 10 Kilometre | ₹6,818.07 | ₹68,180.70 |
| 3Supply of electric fuse complete with fuse block made of PBT for Railway signaling as per IRS-S-75/2006 Rev 2 or latest, fuses non-deteriorating type low voltage, to suit Specn. No. IRS: S- 78/92 or latest, 2 Amp/ 4Amp/ 16Amp/400 mA fuses in ratio of 60:20:10:10. Fuse block shall be suitable for round head type fuses. (Inspection: RDSO). | 810 Numbers | ₹203.09 | ₹1,64,502.90 |
| 4Supply of CLS Signal post 4.6 M and ladder 4.5 M long with base and platform as per RDSO spec.No.IRS-S-6/81 or latest. (Inspection:RITES) . | 90 Numbers | ₹20,731.67 | ₹18,65,850.30 |
| 5Supply of CLS Signal post 3.6 M and ladder 3.5 M with bases and platform as per RDSO spec.No.IRS-S-6/81 or latest. (Inspection:RITES) . | 80 Numbers | ₹17,831.13 | ₹14,26,490.40 |
| 6Supply of colour light signal unit 2 Aspect complete without lamp holder, lamp, lenses and signal transformer as per IRS -S- 26/64 Ver. 1 and RDSO Drg no.SA-23001 A/ M(Adv.) or latest. (Inspection:RITES) . | 90 Numbers | ₹17,395.68 | ₹15,65,611.20 |
| 7Supply of 3/4 Aspect colour light signal unit complete without holders, lamps, lenses and signal transformer as per RDSO Drg. No. SA-23002 A/M(Adv), Alt-9 or latest respectively. Specification no.IRS:S-26/64 Rev 1 or latest. (Inspection: RITES). | 80 Numbers | ₹20,453.05 | ₹16,36,244 |
| 8Supply of Key lock checking relay, Type TMA 24V DC with 2F/2B contacts configuration with different wards combination as per RDSO spn. No. RDSO/SPN/219/2016 ver 1.0 with Amendment-1 or latest confirming to IRS:S-23, S-34 and S-46. Details of ward combination will be provided during execution of work. (Inspection: RDSO). | 65 Numbers | ₹6,707.17 | ₹4,35,966.05 |
| 9Supply of Relay, plug in type, style QNA1, DC neutral line 24V DC, 12F/4B contacts, Front and back contacts metal to carbon with plug board, retaining clip and connectors conforming to BRS-931A,IRS S 60/78, IRS S 34/68 and IRS-S-23/88 or latest (as applicable). The interlocking code for this unit shall be ABDFH.(Inspection: RDSO). | 310 Numbers | ₹3,084.16 | ₹9,56,089.60 |
| 9Supply of Relay, plug in type, style QN1, DC neutral line 24V DC, 12F/4B contacts, Front and back contacts metal to carbon with plug board, retaining clip and connectors conforming to BRS-931A,IRS S 60/78, IRS S 34/68 and IRS-S-23/88 or latest (as applicable). The interlocking code for this unit shall be ABCDE.(Inspection: RDSO). | 900 Numbers | ₹3,084.16 | ₹27,75,744 |
| 10Supply of Relay plug in type, style AC LED, all aspect AC lamp proving relay unit with inbuilt current transformer type slow to release neutral line relay 4F/4B contacts,front & back contacts metal to carbon, shall be suitable for working in series with the 100 V AC, LED signal lamp rated at 15 W confirming to RDSO spec STS/E/ Relays/AC Lit LED signal/09-2002 Amdt1, BRS:941A, IRS-S-34 & IRS-S-23/88 or latest with latest amendments as applicable. The interlocking code for this unit shall be ABDHK type. (Inspection: RDSO). | 410 Numbers | ₹5,531.34 | ₹22,67,849.40 |
| 11Supply of Electronic Timer Relay 24 V DC , 60 Sec/120Sec as per RDSO Spec. IRS:S 61/2000 (Amend.3) or latest. ( Inspection :RDSO). | 27 Numbers | ₹3,274.73 | ₹88,417.71 |
| 12Supply of Apparatus case Large with 'E' type lock and key ward no.42 and handle as per RDSO drg. No. RDSO/S-11500 or latest. (inspection: RITES). | 164 Numbers | ₹18,726.11 | ₹30,71,082.04 |
| 13Supply of Apparatus case half with 'E' type lock and key ward no.42 and handle as per RDSO drg. No. RDSO/S-11500 or latest. (inspection: RITES). | 68 Numbers | ₹14,965.61 | ₹10,17,661.48 |
| 14Supply of ARA terminal block 25 mm centre small M-6 terminal made of PBT as per RDSO drg. no.SA-23741-A,(Alt.-4) spec.no.IRS-S-75/2006 amendment -2 or latest. RDSO/SPN/189/2004Ver. 3.0 (Rev:2) or latest as applicable. (Inspection: RDSO). | 8,000 Numbers | ₹56 | ₹4,48,000 |
| 15Supply of screw less mounted 2.5 sq.mm,4-wire front entry, two input two out put, Disconnected cage clamp terminals block for test and measurement (Wago or Phonex or Elmex) as per site requirement. As per RDSO/SPN/189/2004. The colour will be decided by Eng. in charge (Preferably in Blue, Red & Grey colour in the ratio of 1:2:3). (Inspection: RDSO). | 7,625 Numbers | ₹128.98 | ₹9,83,472.50 |
| 16Supply of Steel carrier Rail 35x7.5mm/0.039 in thick unslotted, yellow with Chrome Wago or similar as per RDSO/SPN/189/2004 Ver.3.0 or latest. (Inspection : Consignee). | 300 Metre | ₹164.23 | ₹49,269 |
| 17Supply of End and Intermediate Plate 2.5mm/0.098 in Thick Wago or similar as per RDSO/SPN/189/2004 Ver.3.0 or latest. (Inspection : Consignee). | 2,160 Numbers | ₹20.49 | ₹44,258.40 |
| 18Supply of screw less end stop 10mm/0.394 in wide carrier rail DIN 35 Grey Wago or similar as per RDSO/SPN/189/2004 Ver.3.0 or latest. (Inspection :Consignee). | 1,080 Numbers | ₹17.96 | ₹19,396.80 |
| 19Supply of Spare booms for ELB as per RDSO Drg. No. RDSO/S-11600 or latest and RDSO spec no. RDSO/SPN/208/2012 or latest.(Inspection: RITES) . | 54 Set | ₹27,917.43 | ₹15,07,541.22 |
| 20Supply of low current Clamp meter digital type with AC/DC clamp, three & three forth digit (3 & 3/4 digit).For Measurement of DC/AC currents from micro Amp and up to 1000A,Voltage up to 600V, resistance up to 40 M and frequency up to 1 MHz with set of leads & carrying case. Model - DCM 39A or equivalent/higher make Make: Stanlay SCM 222/Motwane/Fluke/Rishabh or similar/superior.( Inspection: Consignee). | 27 Numbers | ₹16,144.95 | ₹4,35,913.65 |
| 21Supply of Laser jet printers Make Canon Image CLASS MF 275 dw or similar as per the Instruction of officer incharge. (Inspection: Consignee). | 1 Numbers | ₹40,036.68 | ₹40,036.68 |
| 22Supply of tool kit as per tech spec. given below: (1) Digital Multi Meter suitable for axle counter ranges 20 Amp AC/DC make protek 506 or similar- 1 no. (2) Digital clamp Multi Meter range up to 100 Amps for AC/DC current make SEW or similar - 1 no. (3) Leather Tool Bag for keeping tool kit -1 no. (4) Plier Sealing with sealing code bit -1 no. (5) Plier Wire Cutting 8" make Taparia or similar -1 no. (6) Nose Plier 4" make Taparia or similar -1 no. (7) Wire Stripper - 1 no. (8) Screw Driver set mutli port type -1 set (9) Track shunt resistance .5 ohm -1 no. (10) Soldering Iron 230V AC/65 watt -1 no. (11) Soldering Iron 230V AC/35 watt with diffrerent type replacement soldering head - 1 no. (12) Soldering Iron 110V AC/35 watt -1 no. (13) Measuring Tape steel 30 meters - 1 no. (14) Measuring Tape steel 3 meters - 1 no. (15) Rechargable Torch Superior quality -1 no. (16) File Flat 8" long - 2 nos. (17) File Round smooth 8" long - 2 nos. (18) File Flat Bsterred 8" long - 2 nos. (19) Electric Drill Machine Portable 6mm make wolf or similar -1 no. (Inspection: Consignee). | 27 Set | ₹56,130.47 | ₹15,15,522.69 |
| Schedule C · Supply & Execution Items | |||
| 1Supply,installation & commissioning of Emergency Sliding boom complete with all accessories. (Inspection: RITES for supply portion). | 27 Set | ₹2,67,450 | ₹72,21,150 |
| 2Supply, installation, testing and commissioning of Remote terminal Unit (RTU) 64 digital input and 16 analog input for LC gates. This includes a set of 4 wire leased line modem 57.6 kbps speed, protocol V42 for interlinked maintenance of RTU as per RDSO specification no. IRS S 99/2006 amendment 3 or latest. (Inspection: RDSO). | 27 Numbers | ₹1,92,938.03 | ₹52,09,326.81 |
| 3Supply and fixing of retro-reflective P/G/C markers with complete fittings as per drg. No. NR/S&T/CON 6.2/97. All material required for the job such as MS sheet, MS angle, Nut and bolts, paint and painting materials will be supplied by the Contractor . (Inspection: Site Engineer). | 108 Numbers | ₹850.84 | ₹91,890.72 |
| 4Supply, installation and commissioning of maintenance free separate earthing kit as per RDSO spcn. no. RDSO/SPN/197 Ver. 1.0 or latest and drg. no. SDO/RDSO/E&B/001 dated 19.09.2008 or latest. Basic earthing kit- 1 set consisting of [a] The earth electrode shall be UL listed and of minimum 17.0mm diameter and minimum 3 Meter long and minimum copper bonding thickness shall be of 250 microns of 99.9% electrolyte grade copper.-01 nos. [b] Earth enhanching compound RDSO approved in sealed bags of 10 kgs each-03 nos. minimum [c] Copper bus bar of Size 200 mm X 25 mm X 6mm-01 No. [d] MEEB 300mm X 25mm X 6mm-01 no. [e] 35 sq. mm.copper cable to connect earth electrode to MEEB- 15 mtrs. approx. and all other materials and cables required for installation. Work to be carried out in supervision of Site engineer. Commissioning certificate to be given by OEM. (Inspection: Consignee) | 52 Numbers | ₹17,451.78 | ₹9,07,492.56 |
| 5Supply and installation of earth electrodes as per std.practice. The item includes digging of pit in earth, 3 Mtrs. deep and fixing earth electrode pipe. Casting of cement concrete enclosures as per drg. no. (NR/S&T/CON/6.4/97) or latest. The soil treatment shall be done as per std. practice. The item includes provision of mild steel flat of size 35mm x 6mm (as per IRSEM) an nut bolted connection of MS flat with earth electrode. The other end of mild steel flat to be connected to block instrument,cable sheath of power equipment, signal base, apparatus case,CT rack / relay racks,other equipments as per the instruction of Engr. at site & IRSEM. Earth connection Signal & location boxes to be done Drg.No. 19-D6 of IRSEM App II or latest. Complete materials such as earth electrodes asper Drg.No. (NR/S&T/CON/6.3/97) or latest , cement,wiring material, nut bolt for connection & mild steel flat of size minimum 35mmx6mm or 210 sqm as per SEM etc. to be supplied by the contractor. Inspection by Consignee for supply of earth electrode. (Material Inspection-RITES). | 564 Numbers | ₹2,680.81 | ₹15,11,976.84 |
| 6Supply, installation & wiring of Earth leakage detector (12 Channel) for monitoring different AC and DC supplies including all accessories as per specification no. RDSO/SPN/256/2025 VER:2.0 or latest and stipulations of tender document. (Inspection: RDSO). | 27 Numbers | ₹1,66,606.70 | ₹44,98,380.90 |
| 7Boring & trenchless cabling along with supply and insertion of HDPE self- lubricated pipes of 90 mm nominal dia (DN) with material classification as PE- 80 and Nominal Pressure PN-6 as per IS:4984-95 (with latest Amendments) in the bore for the laying of Signaling/Telecom/Power cables under the track/road. Depth of horizontal boring should be minimum 1500 mm from bottom of rail flange/Road level. (Cable laying is covered separately). (Inspection of HDPE Pipe: RITES). | 5,072 Metre | ₹1,042.76 | ₹52,88,878.72 |
| 8Supply, testing and laying of 2nd class well burnt bricks in trench breadth wise over the top of cable throughout i.e. 8 bricks in one meter overwhole of the cables. Bricks shall be got staked and got inspected by Rly.Representative before laying. (Inspection : Consignee). | 6,48,000 Numbers | ₹5.14 | ₹33,30,720 |
| 9Supply and installation of RFID electronic marker for S&T underground cable with Programmable memory for saving the user specific data inside the RFID electronic marker memory chip,later recordable by electronic marker locator during locating (10 cm diameter with floating coil to keep detection circuit always Horizontal for better detection) which can be burried to depth of 5ft Placing in trench. (Inspection : Rites). | 810 Numbers | ₹2,858.49 | ₹23,15,376.90 |
| 10Supply and fixing of G.I. pipe 75/80 mm dia, 3.6 mm thick, as per specn No. IS-1239, Medium grade, perforated at a distance of 20 CM or less of required length at culverts/ bridges/along the cuttings, suitably concreted at both ends as per drg. No. (NR/S&T/CON/1. 4/97). G.I. clamps of M.S. flats bolts & nuts to be supplied by the contractor. (Inspection: Site Engineer). | 720 Metre | ₹859.62 | ₹6,18,926.40 |
| 11Fabrication & Supply of domino type operating cum indication panel for way side station of Minimum 12 x 7 exchangeable units of size 54 x 34 mm (Siemens panel size) and cover plates with Tag Blocks / terminals, wires, angle irons etc. depicting the yard layout with signals,points, track circuits,operating / emergency push buttons, counters, SM's key housed in a steel metal cabinet as per approved panel diagram and RDSO spec. no.RDSO/SPN/186/2004 or latest. ( Inspection :Consignee). | 2,484 Numbers | ₹636.54 | ₹15,81,165.36 |
| 12Supply & installation of external Modem for provision of T-networking of data logger with LC gate with necessary accessories. (Inspection: Consignee). | 27 Numbers | ₹25,968.95 | ₹7,01,161.65 |
| 13Fabrication, supply and fixing of relay racks of size 2200 mm x 690 mm along with scaffolding as per Drg. No. NR/S&T/CON/4.3/97-A made of angle iron of size 45mm x 45mm X 6mm alongwith outer frame made of angle iron size 65mm x 65 mmX 8 mm fitted with M.S. squares bars duly ionized along with description strips to accommodate Plug-in-type relay groups/Point contractor units/ Route checking relays etc. Scaffolding / cable carrier to be fabricated of angle iron of size 35 mm X 35mm X 6mm and flat of size 25mm X 5mm as per instructions of site Engineer. The Separation between two flats shall be 250 mm or less as per site requirements. All fixing material like anti-tilting device if required, bolts, nuts, washers, insulators, shoe, angle irons, flats, L - bolts, sand, cement & concrete etc. will be supplied by the contractor. This also includes cleaning, priming by Red oxide, painting of rack will be power coated and writing of description of relays by Standard mark paints. (Inspection: Site Engineer). | 27 Numbers | ₹19,827.03 | ₹5,35,329.81 |
| 14Fabrication, supply and fixing of cable termination board of size as per Drg. No.NR/S&T/CON/4.1/97-A made of angle iron of size 45mm x 45mm x 6mm alongwith outer frame made of angle iron of size 65mmx 65mmx 8mm duly fitted with Bakelite sheet of size 6mm thick. This also includes fixing of ARA terminals & fuse bases. Supply and fixing of hard wood of size 70cmx 25cmx 4cm in the back for jamming of cables. All the fixing materials like bolts, nuts, washers, Insulators, shoe, angle irons, flats, L- bolts, cement, sand and concretes etc. will be supplied by the contractor. This includes cleaning, priming by red oxide, painting & writing of description etc. with standard mark paints. (Inspection: Site Engineer). | 27 Numbers | ₹21,421.62 | ₹5,78,383.74 |
| 15Supply, installation, wiring and commissioning of secured L.C. Gate electronic 1+6 nos Telephone System with inbuilt voice recorder in 1+6 configuration with central supply as per Specification No. RDSO/SPN/TC/51/2011 Rev. 3.0 or latest. Supply of L.C. Gate Telephone System with inbuilt voice recorder in 1+6 configuration with central supply as per Specification No. RDSO/SPN/TC/51/2011 Rev. 3.0 or latest. (Inspection: RDSO). | 22 Set | ₹81,385.54 | ₹17,90,481.88 |
| 16Supply and installation of optical fibre cable joint enclosure as per TEC spec no.GR/OJC-02/01/ March 99 with latest amendment and splicing of optical fibre cables (24 fibres & testing). This includes provision of jointing kit(RCC/Prefabricated) as detailed in the technical specification and as advised by engineer at site. (Inspection - Consignee for supply portion). | 23 Numbers | ₹17,313.49 | ₹3,98,210.27 |
| Schedule D · Execution Items | |||
| 1Foundation, Installation, testing & commissioning of Electric lifting barrier complete with panel,motor,booms, weights,warning bells hooters etc. & key chain interlocking along with electric lever locks includes casting of foundation for gate machines, installation & wiring of hooters to make the system as per approved diagrams/plans & as per instruction of site engineer. This also includes fixing of E Type lock, both lifting barriers alongwith boom locking arrangements. This also includes fixing of E Type lock, both lifting barriers along with boom locking arrangements, fixing & wiring of lever lock,cabling, power supply connection & wiring with complete outdoor work as per approved drawing, wiring etc. (Inspection: Site Engineer). | 27 Job | ₹67,994.73 | ₹18,35,857.71 |
| 2Casting, concreting and curing of foundation for main signal as per Drg. no. NR/ S&T/ CON/2.1.97 all material such as anchor bolts cement & aggregate to be supplied by contractor. (Inspection: Site Engineer). | 170 Numbers | ₹10,822.90 | ₹18,39,893 |
| 3Fixing of CLS surfacebase, bolting on the foundation. Erection of CLS post with signal unit on the top or on an offset bracket and fitting ladder and guard to the post at the top. Concreting ladder base and embedded into the ground with supporting bracket in the middle, blanking of the ladder for a distance of 1 feet between the height 6' 9" and 7' 9" from the rail level by MS angle and MS sheet 6 mm thick wherever required. This includes provision of wooden (sal) cross arm 1M x 1M for CLS unit prior to the commissioning,fixing of lenses, lampholder/lamp current regulator and hoods of CLS unit, terminating cables, wiring the CLS unit & fixing the signal.Elevation & distance of foundation from track shall be in accordance with schedule of dimension for Indian railways published by Govt. of India and approved drawings. All items for the above works except signal unit, LED signal, Signal post, base and ladder shall be supplied by the contractor including but not limited to the following: (i) "U"bolt for offset brackets. (ii) Wooden cross arm 1mtr. x 1 mtr. (iii) MS angle and MS sheet for blanking of ladder. (iv) Wire mesh guard, lock for unit if required, nuts and bolts etc. for the following: (V) Supply and fixing of Signal Number Plate with complete fittings as per standard railway practice.Installation, erection,wiring of 2 aspect color light signal. (Inspection: Site Engineer). | 90 Numbers | ₹3,024.08 | ₹2,72,167.20 |
| 4Fixing of CLS surface base, bolting on the foundation. Erection of CLS post with signal unit on the top or on an off-set bracket and fitting ladder and guard to the post at the top. Concreting ladder base and embedded into the ground with support bracket in the middle, blanking of the ladder for a distance of 1 feet between the height 6' 9" and 7' 9" from the rail level by MS angle and MS sheet 6 mm thick wherever required. This includes provision of wooden (SAL) cross arm 1 mtr x 1 mtr for CLS unit prior to the commissioning, fixing of LED aspect, current regulator and hoods of CLS unit, termination cables, wiring the CLS unit and focusing the signal. Elevation & distance of foundation from track shall be in accordance with schedule of dimension for Indian Railways and as per RDSO practice. All items for the above works except Signal unit, LED signal, Signal post, Base and Ladder shall be supplied by the contractor including but not limited to the following: i) "U" bolt for offset brackets, ii) Wooden cross arm 1 mtr. x 1 mtr., iii) MS angle and MS sheet for blanking of ladder, iv) Supply and fixing of signal number plate (retro reflective) with complete fittings as per standard railway practice. v) Wire mesh guard, lock for unit if required, nuts, bolts etc. for the following: a) Installation, erection, wiring of 3/4 aspect color light signal. (Inspection: Site Engineer). | 80 Numbers | ₹4,670.41 | ₹3,73,632.80 |
| 5Casting, concreting and curing of foundation and erection of App. Cases (Single) as per drg. no. (NR/S&T/CON/2.7/97). All materials such as cement, sand aggregate and anchor bolts shall be supplied by the contractor. App. Case single will be supplied by railways. Contractor is required to execute all type of repair works of foundations if required during inserting the cable for termination. (Inspection: Site Engineer). | 164 Numbers | ₹4,285.45 | ₹7,02,813.80 |
| 6Casting, concreting and curing of foundation and erection of App. Cases (half) as per drg.no. (NR/S&T/CON/2.8/97). All materials such as cement, sand aggregate and anchor bolts shall be supplied by the contractor. App. Case Half will be supplied by railways. Contractor is required to execute all type of repair works of foundations if required during inserting the cable for termination. (All concrete work must be ratio of cement, coarse and sand aggregate 1:3:6). (Inspection: Site Engineer). | 68 Numbers | ₹4,066.69 | ₹2,76,534.92 |
| 7Preparation & fixing of Bakelite hylum sheet 910x 800 x 6mm and teak wooden shelf 900mm x 450mm x 25mm duly fixed by angle iron piece of different size inside all the app. Cases. Hylum board shall be fixed on an angle iron frame of 25mmx 25mm x 3mm. Angle iron frame will be fixed in location boxes secured by nuts & bolts. Fixing of fuses, ARA terminal plug in type 'Q' series relays and other type relays on square bars fixing and jamming of cables with 2 inch thick salwood plank provided at the bottom.This will include opening, pasting and jamming armour of each cable in the hole drilled separately for each cable through the salwood plank & all cable entry points on location boxes, location huts, JB's relayroom/battery room to be closed with suitable masonry works covered with sand and plastering. Description for terminal drawing of circuits, inside app. Case. Painting from out side as well inside with red oxide and aluminum paint iscovered separately. Size of lettering will be 100 mm or as per instructions of Engineer at site. All materials including hard wood shelf, hylum board, salwood plank, angle iron square bar, wire and wiring material as per the IRS specn., PPTC fuses 2/6A with suitable length copper lugs crimped to fix on an ARA terminal block, bases,nuts and bolts and other items shall be supplied by the contractor. Relays,ARA terminals,non- deteriorating type HRC fuses only shall be supplied by the railways. (a) Preparation of App. Case single involving wiring of relays. (Inspection: Site Engineer). | 164 Numbers | ₹5,372.57 | ₹8,81,101.48 |
| 8Preparation of App. Case half not involving wiring of relays which includes following- (i)Preparation and fixing of Bakelite hylum sheet 450x800x6 mm and teak wooden shelf 450x450x25 mm duly fixed by angle iron piece of different size inside all the app. Cases. Hylum board shall be fixed on an angle iron frame of 25mm/25mm/3mm. Angle iron frame will be fixed in location box secured by nuts & bolts. (ii) Fixing of fuse ARA terminal, plug in type Q series relays and other type of relays on square bars, fixing and jamming of cable with 2 inch thick salwood plank provided at the bottom. This will include opening, twisting and jamming armor of each cable in the hole drilled separately for each cable through the salwood plank and of cable entry points on location boxes, location nuts JB's relays room battery/room to be closed with suitable masonry work covered with sand & plastering. (iii) Wiring description for terminal,drawing of circuits inside app Case. Painting from outside as well inside with RED oxide aluminum paint is covered separately. Size of lettering as per instructions of Engr. at site. (iv )All material including teak wood shelf, hylum board, salwood plank, angle iron square bar, wire and wiring material as per the IRS spec.,PPTC fuses 2/6A with suitable length copper lugs crimped to fix on an ARA terminal block and bases nuts and bolts and other items shall be supply by the contractor. Relays, ARA terminals,Non deteriorating type HRC fuses only shall be supplied by the Railways. (Inspection: Site Engineer). | 68 Numbers | ₹3,368.15 | ₹2,29,034.20 |
| 9Wiring of relays in relay room/relay huts as per approved wiring diagrams. All material required including indoor cables and wires of 1x1, 1 x0.6, 3 /0.29, 16/0.2, 40 x 0.6, 40 x 1, 60 x 0.6, 60 x 1 dia of copper conductor as per NR practice conforming to IRS specifications, resistance and condensers is to be supplied by the contractor. This also includes wiring from CT rack to tag block, tag block to relays & wiring of fuse etc. required in connection with relay room /relay hut wiring and soldering, dressing, bunching, lacing, fixing of relay bases etc. and provision of LED indication of vital relays in relay room and provision of potential free contacts for relays on tag block for data logger as per instruction of site Engineer. This also includes dressing, bunching, lacing and fixing of relay bases. Indoor cable/ wires shall be duly inspected by RDSO. Indoor cable/wires shall be as per Spec. No. IRS-S76/89 (Amd. 3 or latest). (Inspection: Site Engineer). | 1,600 Numbers | ₹383.10 | ₹6,12,960 |
| 10Earth work for excavation & refilling around location boxes and signals etc. where neccesary including 50 m lead and 1.5 m lift. The lead is to be measured from center of gravity of location to the centre of filling & lift from main ground level. The earth work should be well rammed including breaking of clods, levelling and dressing etc. as per instructions of site Engr. (Inspection: Site Engineer). | 252 cum | ₹117.23 | ₹29,541.96 |
| 11General concrete work in cement, coarse sand and aggregate ratio 1:3:6 scattered at different places for items not covered in above schedule. Volume of foundation also includes volume of C.I. base, anchor bolts. Coarse sand, aggregate 25mm and cement to be supplied by contractor. (Inspection: Site Engineer). | 134 cum | ₹2,397.12 | ₹3,21,214.08 |
| 12Excavating and refilling of trench in Normal Soil to the level of ground with rammed earth as per drg. No.(NR/S&T/CON/1. 1/97-A) so as not to form a drain 0.3 Mtrs. Wide & 1 Mtr. Deep on both side of the station along side the track. It shall confIrm to the safe distance as per signalling and cable plan. It also includes clearance of routes of trees & bushes. Lesser depth due to site conditions shall be paid proportionately after obtaining prior approval from not below than JAG officer. (Inspection: Site Engineer). | 81,000 Metre | ₹54.05 | ₹43,78,050 |
| 13Excavating and refilling of trench 0.3 Mtr. Wide and 1 Mtr. Deep on pitched/Stone/bricks paved surface, road crossing/platform etc. and restoring the surface to its original conditions. Lesser depth of the trench is to be paid proportionately.(Inspection: Site Engineer). | 2,700 Metre | ₹118.03 | ₹3,18,681 |
| 14Laying of signaling/Telecom/power cables of different sizes as per drg. No. (NR/S&T/CON/1. 1/97) and as per cable route plan approved by Railways and meggering of cable before and after its laying of all type of outdoor cables. Meggering to be done for each drum separately. Meggering sheets to be supplied and filled up by contractor and submitted to railways. (Inspection: Site engineer). | 4,50,000 Metre | ₹6.04 | ₹27,18,000 |
| 15Installation of KLCR & its box in location boxes/Gate lodge, supply & installation of heavy duty push button, LED indicator on M S sheet of 4.5 mm thick inside location box/Gate lodge for crank handle locking. The work includes fixing & wiring of magneto telephones, wiring of KLCR, push buttons and termination of tail cables as per instructions of site Engineer. All material except KLCR relay & its box and magneto telephone to be supplied by the contractor. This also includes fixing of wards on point machine.Foundation & installation of location box is covered as separate item of schedule. (Inspection: Site Engineer). | 54 Numbers | ₹7,845.88 | ₹4,23,677.52 |
| 16Brick work with well burnt bricks in foundations and plinths with cement and sand (ordinary )mixture of 1:4 ratio. All material is to be supplied by the contractor. (Inspection: Site Engineer). | 88 cum | ₹3,019.88 | ₹2,65,749.44 |
| 17Geo-Tagging route in trench for signalling or telecom cable, with GNSS or similar coordinates acquired generally with upto 10 cms location accuracy (in accuracy upto 40 cms range permitted for locations with tree cover etc., final accuracy depending on weather & interference conditions), with depth of cable in trench based on ground level at that location to be indicated.Data Output should be mapped provided on .kml format or similar format with integrated depth data of cables-mapped. Equipment utilised will be cable route locator with GNSS/GPS or similar RTK/DGPS or similar receiver mounted on equipment.Equipment utilised should be cable route locator with suitable transmitter power using low frequencies of RTK/DGPS or similar mounted directly on equipment with RTK/DGPS or similar correction service with high precision for upto 10 cms accuracy, with utility mapping software/web based interface used on mobile phone (software/web based interface should take data via Bluetooth/WiFi etc from both Cable locator & RTK/DGPS or similar GNSS receiver, with Auto correction Catalyst service simultaneously to provide integrated data output).Additional map required with cable distance from nearest track/OHE Pole to be included and provided as hard copy with coordinates of cable mentioned. Separate color code to be used for different trench for S&T cables, capture images for Manhole/OFC JC Location with nearest reference point, if applicable.In routemap, Geotagging to be done at interval distance of 30 meters or less for approximate straight path. And at track crossing, diversion, culvert, jointing locations, as per site condition.Data output will be provided on USB & Hard copy print.Make: Rycom Pathfinder, 3M or similar for the data acquisition.Training on Geo-Tagging of cable route included or similar. Contractor shall provide access of all data/maps etc. for 5 years,Inspection-Consignee,Inspection charges-Nil,Payment terms-100% after execution. | 90 Kilometre | ₹38,855.22 | ₹34,96,969.80 |
| 18Provision of fencing arrangements for the location boxes. The work involves erecting posts using GI pipes 25 mm dia - 3m long near the location boxes at an interval of 2m and providing fencing using barbed steel wires around thelocation boxes. The GI pipes shallbe buried to a depth of 1m.Thebarbed wire shall be provide dusing14 SWG GI wire (2 wires)barbed at 6"interval. The wiresshall be provided from ground level to the top of post at an interval of6". The work also includes erectionof two rail posts, fabrication of agate using MS angles 50x50x5mmand MS flats 50mmx3mmand fixingit on the rails and provision oflocking facility using E Type lock ofsame ward used at Location box asper the instructions of Railwayrepresentative at site. (Rails ofdifferent lengths will be supplied byRailways at nearest PWI depot. TheContractor has to transport, cutand erect the rails to the requiredlengths as per requirement).[GIpipes 25mm thick, barbed steelwire, MS angles50mm x 50mm x5mm and MS flats 50mm x 5mmfor fabrication of gate, E type Lockand all other miscellaneous materials required for the workshall be supplied by the contractor.Fabrication and erection must bedone by professional fabricator withgood workman ship. The item shallbe used at the location boxeslocated near populated areas.Measurement unit is Sqm= area inSquare meter, Area of land coveredby the fencing. (Inspection:Consignee). Inspection Charges:None. Payment Terms:100% after execution. | 928 Sqm | ₹1,159.92 | ₹10,76,405.76 |
| 19Cleaning , Scrapping , Painting and lettering of all newly installed and existing gears such as signals, point equipment, track circuit equipment with T.C. no on rail app. Cases JB. TL JBs point rodding cranks, compensators etc. including gate equipment if existing in station section as per the provision of IRSEM. all painting material to be supplied by the contractor. all paints (ISI marked) shall be approved by Railway Engineer prior to painting and certificate to this effect submitted to railway. this item also includes wiring and painting requirment of all indoor and outdoor gears along with making of all circuit nos.near terminal and terminal boards track in app. cases junction boxes relay room. SMs room wiring of relay nomenclature fuse nos. and equipment nomendature as the approved plans and as per provision of IRSEM at way side station. (Level crossing gate).(Inspection-Site Engineer). | 27 LC Gate | ₹23,034.08 | ₹6,21,920.16 |
| 20Dismantling of lifting barrier/ gate leaves complete set along with winch, wire rope, boom locking arrangement , all dismantled material to be transported and stacked in the store of concern SSE/sig/Incharges or any other store of N.R as per consignee. Transportation charges are covered in item no. 62. Note :- Before dismantling joint survey is to be done with the site engr. and report to be submitted to the site engr. (1 Job= 1 Lifting barrier etc. at one LC Gate). | 27 Job | ₹3,371.49 | ₹91,030.23 |
| 21Blowing/Drawing of OFC cable in the HDPE duct by mechanical system. (Inspection : Site Engineer). | 60 Kilometre | ₹10,537.60 | ₹6,32,256 |
| Total | ₹11,95,06,606.13 | ||
The total matches the advertised value.
Documents
- Notice inviting tenderOpen document
- Typical Drawings of LC GatesTypicalDrawingsofLCGates.pdfDirect link not supplied in the PDFView reference in PDF ↗
- TENDER DOCUMENTTENDERDOCUMENT27LCINTERLOCKINGFZRDIV.pdfDirect link not supplied in the PDFView reference in PDF ↗
- Annexure-V(A)Annexure-V(A).pdfOpen document
Documents to submit
Commercial-Compliance
- Document optional
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Technical-Compliances
- Document required
Upload filled & signed Annexure-D:"Declaration regarding constitution of firm".(Copy attached with Vol-I of tender document)
- Document required
Upload filled and signed Annexure-M:"Mandatory Certificate to be submitted by tenderer alongwith the tender documents.". (Copy attached with Vol-I of tender document).
- Document required
Upload filled & Signed Annexure-H Work in Hand - in support of Bid Capacity (Mandatorily for tender value more than Rs.20 crore) (copy of format available in Vol-I of Tender Document).
- Document required
Upload filled and signed Annexure-I:Detail of Contractual Payment received in previous three financial years and the current financial year.(Copy of format available in Vol-I of tender document)
- Document optional
Upload filled & signed Annexure-J:Real Time Gross Saving (RTGS)/National Electronic Fund Transfer(NEFT) Model Mandate Form (copy of format available in Vol-I of tender document)
Show all 15
- Document required
Upload filled & signed Annexure-N Contractual payment received in last three years - in support of Bid Capacity (Mandatorily for tender value more than Rs. 20 crore).(Copy of format available under Vol-I of tender document)
- Document required
Upload filled & signed Annexure-Q Mandatory undertaking Regarding Employment/ Partnership of Retired Railway Employees.(copy of format available in Vol-I of tender document).
- Document optional
Upload filled & signed Annexure K-3 & K-4: If tender submitted on behalf of Partnership Firm, relevant Annexures K-3 and K-4 as Declaration to be submitted by the tenderer alongwith tender document.
- Document optional
Upload filled & signed Annexure-C:Declaration form regarding site etc.(Format attached with Vol-I of tender document)
- Document optional
Upload filled and signed Annexure-E List of plant and Machinery.(Copy attached with Vol-I of tender document)
- Document optional
Upload filled and signed Annexure-F List of Engineers/Personnel (Copy attached with Vol-I of tender document).
- Document optional
Upload filled & Signed Annexure-G:Statement of work executed/completed during last 7 years ending last day of the month previous to the one in which tender is invited (Format available in Vol-I of tender document).
- Document required
Upload filled and signed Annexure-I Detail of Annual Contractual Turnover Data for previous 3/4 Years (Copy of format available in Vol-I of tender document)
- Document optional
Upload filled & signed Annexure-AB STATEMENT OF DEVIATIONS.(copy of format available in Vol-I of tender document)
Upload filled & signed Annexure-L: Completion Certificate(copy of format available in Vol-I of tender document)
Eligibility
Standard Financial Criteria
- Document required
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less, where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-I, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
Standard Technical Criteria
- Document required
(a)The tenderer must have successfully completed or substantially completed any of the following (by any Government organizations) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited. Three similar works each costing not less than the amount equal to 30% of advertised value of each component of tender, or Two similar works costing not less than the amount equal to 40% of advertised value of the tender, or One similar work costing not less than the amount equal to 60% of advertised value of the tender.
Defination of Similar Work • Any signaling work of PI or RRI or EI or ABS or IBS/IBH involving indoor work.OR• Any work of alteration in PI or RRI or EI or ABS or IBS/IBH.Note 1: Tenderer may be required to submit the schedule of those works, Completion/Performance Certificates of which have been submitted by him/her in support of 30 /40 / 60% (as the case may be) criterion of similar nature of work.Note 2: The tenderer should be OEM or have an MOU with OEM (OEM of the EI in which alteration is to be done). Tenderer will have to submit the proof of the same with the tender document.
Partnership firm/Joint Venture (JV) / Hindu Undivided Family (HUF) / Limited Liability Partnership (LLP) etc.
Please submit a certificate in the prescribed format (please download the format from the link given below). Non submission of the certificate, or submission of certificate either not properly filled in, or in a format other than the prescribed format shall lead to summary rejection of your offer. ( Click here to download the Format of Self Certification)
Terms & conditions
Bidder declarations (10)
I/we the tenderer (s) am/are signing this document after carefully reading the contents.
I/We the tenderer(s) also accept all the conditions of the tender and have signed all the pages in confirmation thereof.
I/we hereby declare that I/we have downloaded the tender documents from Indian Railway website www.ireps.gov.in . I/we have verified the content of the document from the website and there is no addition, no deletion or no alteration to the content of the tender document. In case of any discrepancy noticed at any stage i.e. evaluation of tenders, execution of work or final payment of the contract, the master copy available with the railway Administration shall be final and binding upon me/us.
I/we declare and certify that I/we have not made any misleading or false representation in the forms, statements and attachments in proof of the qualification requirements.
I/We also understand that my/our offer will be evaluated based on the documents/credentials submitted along with the offer and same shall be binding upon me/us.
I/We declare that the information and documents submitted along with the tender by me/us are correct and I/we are fully responsible for the correctness of the information and documents, submitted by us.
I/we certify that I/we the tenderer(s) is/are not blacklisted or debarred by Railways or any other Ministry / Department of Govt. of India from participation in tender on the date of submission of bids, either in individual capacity or as a HUF/ member of the partnership firm/LLP/JV/Society/Trust.
I/we understand that if the contents of the certificate submitted by us are found to be forged/false at any time during process for evaluation of tenders, it shall lead to forfeiture of the Bid Security and may also lead to any other action provided in the contract including banning of business for a period of upto two year. Further, I/we and all my/our constituents understand that my/our offer shall be summarily rejected.
I/we also understand that if the contents of the certificate submitted by us are found to be false/forged at any time after the award of the contract, it will lead to termination of the contract, along with forfeiture of Bid Security/Security Deposit and Performance guarantee and may also lead to any other action provided in the contract including banning of business for a period of upto two year.
I/We have read the clause regarding restriction on procurement from a bidder of a country which shares a land border with India and certify that I am/We are not from such a country or, if from such a country, have been registered with the competent Authority. I/We hereby certify that I/we fulfil all the requirements in this regard and am/are eligible to be considered (evidence of valid registration by the competent authority is enclosed)
Fees & money
- EMD
- ₹23.9 L
- Tender fee
- None
Important dates
- Published
- 6 Oct 2026, 4:04 pm IST
- Bidding starts
- 16 Oct 2026
- Closes
- 30 Oct 2026, 11:30 am IST
Similar open tenders
- S&T work for Interlocking of 28 Nos Non-Interlocked LC gates having TVU >20000 and < 5000…Ministry of Railways · Closes 12 Oct 2026
- S&T work for Interlocking of 28 Nos Non-Interlocked LC gates having TVU >20000 and < 5000…Ministry of Railways · Closes 30 Oct 2026
- TRD work in c/w Interlocking of 55 Nos. Non-Interlocked LC gates having TVU >20000 and <5…Ministry of Railways · Closes 22 Oct 2026
- Electrical work in c/w Provision interlocking of 74 No. (55 No. of FZR Div) Non interlock…Ministry of Railways · Closes 27 Oct 2026
- Electrical work for - (A)Interlocking of Non-interlocked LC Gates KR-4 & GCF-63 having TV…Ministry of Railways · Closes 28 Oct 2026
- Electrical work for - (A)Interlocking of LC Gates NC-7, NC-8 & NC-75 having TVU>10,000 al…Ministry of Railways · Closes 21 Oct 2026
- Provision of Relay Hut at (10 Nos Level crossings) for Gate Signalling at Non Interlocked…Ministry of Railways · Closes 14 Oct 2026
- (1) Construction of Relay Hut at Non-Interlocked LC gates having TVU-10000 over Nagpur di…Ministry of Railways · Closes 22 Oct 2026
Search similar in the explorerFind this tender in the explorer