Professional Large Format Display (V2)

OPTION CLAUSE: The Purchaser reserves the right to increase or decrease the quantity to be ordered up to 25 percent of bid quantity at the time of placement of contract. The purchaser also reserves the right to increase the ordered quantity up to 25% of the contracted quantity during the currency of the contract at the contracted rates. The delivery period of quantity shall commence from the last date of original delivery order and in cases where option clause is exercised during the extended delivery period the additional time shall commence from the last date of extended delivery period. The additional delivery time shall be (Increased quantity ÷ Original quantity) × Original delivery period (in days), subject to minimum of 30 days. If the original delivery period is less than 30 days, the additional time equals the original delivery period. The Purchaser may extend this calculated delivery duration up to the original delivery period while exercising the option clause. Bidders must comply with these terms.

Bidder shall submit the following documents along with their bid for Vendor Code Creation:

• a.Copy of PAN Card.
• b.Copy of GSTIN.
• c.Copy of Cancelled Cheque.
• d.Copy of EFT Mandate duly certified by Bank.

Data Sheet of the product(s) offered in the bid, are to be uploaded along with the bid documents. Buyers can match and verify the Data Sheet with the product specifications offered. In case of any unexplained mismatch of technical parameters, the bid is liable for rejection.

IT equipment shall be IPv6 ready from day one.

Malicious Code Certificate: The seller should upload following certificate in the bid:-

• (a)This is to certify that the Hardware and the Software being offered, as part of the contract, does not contain Embedded Malicious code that would activate procedures to :-
• (i)Inhibit the desires and designed function of the equipment.
• (ii)Cause physical damage to the user or equipment during the exploitation.
• (iii)Tap information resident or transient in the equipment/network.
• (b)The firm will be considered to be in breach of the procurement contract, in case physical damage, loss of information or infringements related to copyright and Intellectual Property Right (IPRs) are caused due to activation of any such malicious code in embedded software.

Manufacturer Authorization:Wherever Authorised Distributors/service providers are submitting the bid, Authorisation Form /Certificate with OEM/Original Service Provider details such as name, designation, address, e-mail Id and Phone No. required to be furnished along with the bid

Scope of supply (Bid price to include all cost components) : Only supply of Goods

• 8.Turnover Bidder Turn Over Criteria: The minimum average annual financial turnover of the bidder during the last three years, ending on 31st March of the previous financial year, should be as indicated in the bid document. Documentary evidence in the form of certified Audited Balance Sheets of relevant periods or a certificate from the Chartered Accountant / Cost Accountant indicating the turnover details for the relevant period shall be uploaded with the bid. In case the date of constitution / incorporation of the bidder is less than 3 year old, the average turnover in respect of the completed financial years after the date of constitution shall be taken into account for this criteria.
• 9.Turnover OEM Turn Over Criteria: The minimum average annual financial turnover of the OEM of the offered product during the last three years, ending on 31st March of the previous financial year, should be as indicated in the bid document. Documentary evidence in the form of certified Audited Balance Sheets of relevant periods or a certificate from the Chartered Accountant / Cost Accountant indicating the turnover details for the relevant period shall be uploaded with the bid. In case the date of constitution / incorporation of the OEM is less than 3 year old, the average turnover in respect of the completed financial years after the date of constitution shall be taken into account for this criteria. In case of bunch bids, the OEM of CATEGORY RELATED TO primary product having highest bid value should meet this criterion.

ISO 9001: The bidder or the OEM of the offered products must have ISO 9001 certification.

Bidder's offer is liable to be rejected if they don't upload any of the certificates / documents sought in the Bid document, ATC and Corrigendum if any.

Timely Servicing / rectification of defects during warranty period: After having been notified of the defects / service requirement during warranty period, Seller has to complete the required Service / Rectification within 15 days time limit. If the Seller fails to complete service / rectification with defined time limit, a penalty of 0.5% of Unit Price of the product shall be charged as penalty for each week of delay from the seller. Seller can deposit the penalty with the Buyer directly else the Buyer shall have a right to recover all such penalty amount from the Performance Security (PBG).Cumulative Penalty cannot exceed more than 10% of the total contract value after which the Buyer shall have the right to get the service / rectification done from alternate sources at the risk and cost of the Seller besides forfeiture of PBG. Seller shall be liable to re-imberse the cost of such service / rectification to the Buyer.

Warranty period of the supplied products shall be 3 years from the date of final acceptance of goods or after completion of installation, commissioning & testing of goods (if included in the scope of supply), at consignee location. OEM Warranty certificates must be submitted by Successful Bidder at the time of delivery of Goods. The seller should guarantee the rectification of goods in case of any break down during the guarantee period. Seller should have well established Installation, Commissioning, Training, Troubleshooting and Maintenance Service group in INDIA for attending the after sales service. Details of Service Centres near consignee destinations are to be uploaded along with the bid.

Buyer Added text based ATC clauses 1 Buyer’s technical specification should be duly stamped, ink signed and uploaded by bidders. Not adherin g will result in rejection. 2 All necessary documents and certificates as mentioned in bid to be provided by the bidders. 3 Items may be rejected after delivery if items do not meet the specified criteria as mentioned in buyer’s t echnical specifications (as attached in buyer added bid specific ATC). 4 Bidder shall not be blacklisted for fraudulent practices with any government department/ agencies/ mini stries or PSU’s as on submission of the bid. A declaration signatory of the bidder must be enclosed. 5 Declaration from OEM that quoted product is not end of life and has residual value of minimum 5 years. 6 Technical specification of the offered product should be available in public domain (OEM website) with m odel name / number. Any mismatch in data sheet and technical compliance will lead to rejection. Also, dec laration from OEM authorized signatory to be submitted. Information will not be change/ tempered post bid submission / till warranty of the offered product. 7 OEM/ bidder should have minimum 01 authorized services centers to the state of consignee to cater afte r-sales services, documentary proof must be submitted. 8 Declaration from OEM that non refurbished material will be used in the supplied projector. 9 Declaration of land border sharing certificates is to be submitted on letter head. 10 Wall mounting kit/stand with necessary wiring/cabling along with installation is required. 11 Malicious code certificate from the OEM to be provided. 12 WiFi/ Bluetooth facility if any available, physically needs to be disabled. 13 HDMI, VGA and DP cables must be provided along with necessary accessories. 14 EMD or EMD exemption certificate must be submitted by the bidders, issued from competent authority. 15 A provision for physically disconnecting Wi-Fi, Bluetooth, Webcam, Microphone and GPS modules at the hardware level must be available. 16 In case provision for physically disconnecting the wireless modules is not feasible, in place kernel-level access (root access), such as USB debugging or develop options, is required for accessing OS kernel files and disabling Wi-Fi Bluetooth, Webcam and microphone at the kernel level. 17 Unique access code to the hidden service menu/ hospitality menu should be provided. 18 Mode of disabling unwanted services like GPS, Microphone. 19 Mode disabling unused ports (USB, C-type, card reader). 20 Developer Option ON-OFF facility should be available. .

Buyer uploaded ATC document Click here to view the file.

Participation by the bidder in RA process would be considered as their consent for extension in offer validity by 30 days by the date of RA initiation.