Browse all bids
eProcureOpenWorks

Proposal for 03 M FOB and HL platform at CPBH station under ADEN/DOS.

Ministry of Railways

DRM Office 2nd floor Pt. DDU Nagar

Delivers to

Ghazipur, Hazipur, Uttar Pradesh

Overview

23 facts from the tender

Ministry of Railways published this works tender on eProcure on 8 Oct 2026, for Ghazipur, Hazipur, Uttar Pradesh. The estimated value is ₹5.5 Cr and the EMD is ₹11 L. It closes on 30 Oct 2026, 12:00 pm IST. Tender ID 92190151 · Ref 26-DDU-SRDEN-II-26-27.

Timeline

  1. Published8 Oct 2026 · 6:25 pm
  2. Closes30 Oct 2026 · 12:00 pm

Bidding

Bid type
Open/Advertised
Contract type
Works - General · Expenditure
Tender type
Open
Tendering section
COS/T2
Bidding system
Single Packet System
Bidding style
Single Rate for Each Schedule
Validity of offer
60 days
Completion period
12 Months
Tender document cost
None
JV / consortium
Not allowed
Ranking order
Lowest to Highest
Expenditure type
Capital (Works)
Pre-bid meeting
None

Buyer

Inviting authority
DDU DIVISION-ENGINEERING/EAST CENTRAL RLY
Organisation type
Central Govt. Ministry/Department
Product category
Railway related Products
Location
Hazipur
City, state
Ghazipur, Uttar Pradesh
Portal
eProcure
Inviting officer
DRM/EngineeringDDU DIVISION-ENGINEERING/EAST CENTRAL RLY

Important dates

Published
8 Oct 2026, 6:25 pm IST
Bidding starts
16 Oct 2026
Closes
30 Oct 2026, 12:00 pm IST

Declarations by the buyer

  • Complies with the Public Procurement (Make in India) Order 2017
  • The tender inviting authority confirms this tender does not violate the GFR rules on procurement through GeM
  • Bidders from a country sharing a land border with India must be registered with the competent authority

Schedule of work

67 items
ItemQuantityRailways’ estimated rateAmount
Schedule B · All items of Schedule CPWD DSR 2021
1CARRIAGE OF MATERIALS // By Manual Labour including loading, unloading and stacking for lead less than 0.50 KM // Steel // Cost of carriage including loading, unloading & stacking for first 50 metres380 Tonne₹291.14₹85,187.56
2EARTH WORK // Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. // All kinds of soil3,500 cum₹205.45₹5,53,687.75
3CONCRETE WORK // CEMENT CONCRETE (CAST IN SITU) // Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : // 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)200 cum₹6,833.40₹10,52,343.60
4CONCRETE WORK // CEMENT CONCRETE (CAST IN SITU) // Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: // 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)150 cum₹9,375.20₹10,82,835.60
5REINFORCED CEMENT CONCRETE // STEEL REINFORCEMENT // Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. // Thermo-Mechanically Treated bars of grade Fe-500D or more.70,000 Kg₹89.65₹48,32,135
6REINFORCED CEMENT CONCRETE // CAST IN SITU // Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : // 1:1.5:3 (1 cement : 1.5 coarse sand (zone- III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources)35 cum₹8,364.20₹2,25,415.19
7REINFORCED CEMENT CONCRETE // CAST IN SITU // Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : // 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)55 cum₹10,185.05₹4,31,336.87
8REINFORCED CEMENT CONCRETE // DESIGN MIX CONCRETE // Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in- charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 1.10 times of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. // All works upto plinth level // Concrete of M25 grade with minimum cement content of 330 kg /cum70 cum₹8,683.80₹4,68,056.82
9REINFORCED CEMENT CONCRETE // PRE-CAST RCC // Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but , excluding cost of reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).300 cum₹9,673.50₹22,34,578.50
10REINFORCED CEMENT CONCRETE // PRE-CAST RCC // Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete in shelves, including setting in cement mortar 1:3 (1cement : 3 coarse sand), cost of required centering, shuttering and finishing with neat cement punning on exposed surfaces but , excluding the cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).100 cum₹18,644.60₹14,35,634.20
11REINFORCED CEMENT CONCRETE // FORM WORK // Centering and shuttering including strutting, propping etc. and removal of form for // Foundations, footings, bases of columns, etc. for mass concrete800 Sqm₹307.95₹1,89,697.20
12REINFORCED CEMENT CONCRETE // FORM WORK // Centering and shuttering including strutting, propping etc. and removal of form for // Suspended floors, roofs, landings, balconies and access platform1,000 Sqm₹766.55₹5,90,243.50
13REINFORCED CEMENT CONCRETE // FORM WORK // Centering and shuttering including strutting, propping etc. and removal of form for // Stairs, (excluding landings) except spiral-staircases240 Sqm₹657.75₹1,21,552.20
14MASONRY WORK // EXPOSED BRICK WALL // Brick work with non modular fly ash bricks conforming to IS:12894, class designation 10 average compressive strength in super structure above plinth level up to floor V level in : // Cement mortar 1:6 (1 cement : 6 Coarse sand)100 cum₹7,676.30₹5,91,075.10
15MASONRY WORK // EXPOSED BRICK WALL // Half brick masonry with non modular fly ash bricks of class designation 10, conforming to IS :12894, in super structure above plinth and upto floor V level. // Cement mortar 1 : 4 (1 cement : 4 coarse sand)50 Sqm₹969.65₹37,331.53
16CLADDING WORK // STONE WORK DRY CLADDING // Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. (c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.40 Sqm₹4,474.20₹1,37,805.36
17CLADDING WORK // Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. // Granite stone slab of colour black, Cherry/Ruby red // Area of slab over 0.50 sqm145 Sqm₹4,425.35₹4,94,090.33
18CLADDING WORK // STONE WORK DRY CLADDING // Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.145 Sqm₹1,063.45₹1,18,734.19
19WOOD AND P.V.C. WORK // MISCELLANEOUS-WOOD WORK // Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. // Fixed to openings /wooden frames with rawl plugs screws etc.1,200 Kg₹197.70₹1,82,674.80
20WOOD AND P.V.C. WORK // FRAMES AND TRUSSES // Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). // Sal wood0.45 cum₹1,06,720.85₹36,978.77
21WOOD AND P.V.C. WORK // Providing and fixing 25 mm thick shutters for cup board etc. : // Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. // 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws20 Sqm₹2,818.50₹43,404.90
22WOOD AND P.V.C. WORK // BRASS FITTINGS // Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : // 150x10 mm8 Each₹232.30₹1,430.97
23WOOD AND P.V.C. WORK // BRASS FITTINGS // Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.8 Each₹1,025.65₹6,318
24WOOD AND P.V.C. WORK // GYPSUM BOARD PARTITIONS // Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.30 Metre₹702.60₹16,230.06
25WOOD AND P.V.C. WORK // GYPSUM BOARD PARTITIONS // Providing and fixing to existing door frames. // 30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS: 14856, complete as per direction of Engineer-in-charge.20 Sqm₹3,963.70₹61,040.98
26WOOD AND P.V.C. WORK // MISCELLANEOUS-WOOD WORK // Providing and fixing expanded metal 20x60 mm strands 3.25 mm wide and 1.6mm thick for windows etc. including 62 x19 mm beading of second class teak wood and priming coat with approved steel primer all complete.470 Sqm₹1,277.65₹4,62,381.53
27STEEL WORK // Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.2,50,000 Kg₹111.95₹2,15,50,375
28STEEL WORK // Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. // Hot finished welded type tubes65,000 Kg₹154.90₹77,52,745
29STEEL WORK // Providing and fixing mild steel round holding down bolts with nuts and washer plates complete.4,000 Kg₹88.50₹2,72,580
30STEEL WORK // Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).400 Kg₹612.25₹1,88,573
31FLOORING // Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with local sand, with common burnt clay non modular bricks.6,500 Sqm₹733.30₹36,70,166.50
32FLOORING // TILE FLOORING // Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). // Ordinary cement without any pigment3,000 Sqm₹928.50₹21,44,835
33FLOORING // VITRIFIED FLOOR TILES // Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. // Glazed Vitrified tiles Matt/Antiskid finish of size // Size of Tile 800 x 800 mm180 Sqm₹1,544.20₹2,14,026.12
34ROOFING // Providing, fixing and embedding sand cast iron accessories for rain water pipes in the masonry surrounded with 12 mm thick cement mortar of the same mix, as that of masonry (lead caulking will be paid for separately): // Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. // 110 mm diameter80 Metre₹319.75₹19,696.60
35ROOFING // Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. // Single tee with door // 110x110x110 mm20 Each₹205.45₹3,163.93
36ROOFING // Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. // Bend 87.5 degrees // 110 mm bend35 Each₹132₹3,557.40
37ROOFING // Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. // Providing and fixing of Pre-coated colour or mill finish Aluminium Roofing Accessories in 0.71 mm thickness ,Alloy 31500 (IS designation) [Aluminium Alloy (AA) 3004 (ISO designation)] For color, coating shall be 5-7 microns epoxy primer on both sides of the sheet and polyester top coat 15-18 microns, using self drilling/tapping SS screws of size 6 x 50mm with 3mm thick EPDM seal and SS plain washer complete : // Precoated/mill finish aluminium Ridges plain (500- 600mm)300 Metre₹969.50₹2,23,954.50
38ROOFING // Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. // Providing & fixing at all heights, levels and locations colour finish Aluminium alloy roofing sheets of alloy IS designation 31500, temper Hx8 conforming to IS 737 and dimensions as per IS code 2676 with characteristics of good formability and corrosion resistance. The profile sheets shall be fixed to truss members in slope or required pitch or curvature with Hex cap headed self drilling/tapping Stainless steel screws M6, 50 mm long with 3 mm EPDM seal washer etc. all inclusive of labour, scaffolding, T&P and sundries etc. complete as per directions of the Engineer-In-Charge. (Cost of truss/frame work shall be paid separately). // 0.71 mm, Aluminium Color coated troughed profile with center to center pitch of 200 mm, depth of 32 mm, overall profile width1092 mm, cover width 1000mm.900 Sqm₹1,324.05₹9,17,566.65
39ROOFING // SHEET ROOFING // Extra for providing and fixing wind ties of 40x 6 mm flat iron section.750 Metre₹163.65₹94,507.88
40FINISHING // Painting with aluminium paint of approved brand and manufacture to give an even shade . // Two or more coats on new work3,500 Sqm₹121.45₹3,27,307.75
41FINISHING // EXTERIOR FINISHING // Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : // Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm850 Sqm₹158.95₹1,04,032.77
42DISMANTLING AND DEMOLISHING // Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. // For thickness of tiles 10 mm to 25 mm3 Sqm₹60.50₹139.75
43DISMANTLING AND DEMOLISHING // Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: // G.S. Sheet45 Sqm₹136₹4,712.40
44SANITARY INSTALLATIONS // Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. // Semi rigid pipe // 32 mm dia10 Each₹90.95₹700.32
45SANITARY INSTALLATIONS // Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer4 Each₹3,459.05₹10,653.87
46SANITARY INSTALLATIONS // Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.8 Each₹204.70₹1,260.95
47SANITARY INSTALLATIONS // Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.2 Each₹1,411.15₹2,173.17
48SANITARY INSTALLATIONS // Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.3 Each₹13,036.55₹30,114.43
49SANITARY INSTALLATIONS // Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer- in-charge.8 Each₹7,004.45₹43,147.41
50WATER SUPPLY // C.P.V.C. PIPES // Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge, Concealed work, including cutting chases and making good the wall etc. // 15 mm nominal dia Pipes150 Metre₹441.15₹50,952.82
51WATER SUPPLY // C.P.V.C. PIPES // Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge, Concealed work, including cutting chases and making good the wall etc. // 20 mm nominal dia Pipes120 Metre₹513.75₹47,470.50
52WATER SUPPLY // C.P.V.C. PIPES // Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.-Internal work - Exposed on wall // 50 mm nominal dia Pipes220 Metre₹927₹1,57,033.80
53WATER SUPPLY // C.P.V.C. PIPES // Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.-External work // 40 mm nominal dia Pipes75 Metre₹559.20₹32,293.80
54WATER SUPPLY // BRASS FITTINGS // Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : // 40 mm nominal bore3 Each₹707.30₹1,633.86
55WATER SUPPLY // BRASS FITTINGS // Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : // 50 mm nominal bore3 Each₹878.25₹2,028.76
56WATER SUPPLY // BRASS FITTINGS // Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : // 25 mm nominal bore2 Each₹399.15₹614.69
57WATER SUPPLY // C.I. SLUICE VALVES/ FIRE HYDRANTS & FIXTURES // Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.3,500 Litre₹9.70₹26,141.50
58PILE WORK // Boring with hydraulic piling rigs with power units, providing and installing cast in situ single under reamed piles of specified diameter and length below pile cap in M- 25 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap) : // 300 mm dia piles300 Metre₹2,560.90₹5,91,567.90
59RAIN WATER HARVESTING & TUBEWELLS // Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level. // All types of soil // 300 mm dia80 Metre₹690.70₹42,547.12
60RAIN WATER HARVESTING & TUBEWELLS // Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level. // Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer - in-charge. // 200 mm nominal size dia50 Metre₹951.95₹36,650.07
61RAIN WATER HARVESTING & TUBEWELLS // Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level. // Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. // 200 mm nominal size dia20 Metre₹1,099.25₹16,928.45
62RAIN WATER HARVESTING & TUBEWELLS // Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level. // Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.3 cum₹1,479.25₹3,417.07
63SANITARY INSTALLATIONS // Providing and fixing soil, waste and vent pipes : // 100 mm dia // Sand cast iron S&S pipe as per IS: 1729450 Metre₹1,018.05₹3,52,754.33
64SANITARY INSTALLATIONS // Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. // 100 mm dia // Sand cast iron S&S as per IS - 172925 Each₹530.70₹10,215.98
65SANITARY INSTALLATIONS // Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes : // 100 mm dia pipe35 Each₹163.45₹4,404.98
66WATER SUPPLY // C.P.V.C. PIPES // Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.-External work // 50 mm dia nominal bore600 Metre₹654.20₹3,02,240.40
67WATER SUPPLY // C.P.V.C. PIPES // Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.-Internal work - Exposed on wall // 25 mm dia nominal bore350 Metre₹491.20₹1,32,378.40
Total₹5,48,83,465.34

Bids quote a percentage above, below or at par with these rates · Escalation -23% on every item · The total matches the advertised value.

Documents

10 files

Documents to submit

Commercial-Compliance

  • Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.

    Document optional

  • The tenderers shall submit a copy of certificate stating that all their statements/documents submitted alongwith bid are true and factual. Standard format of certificate to be submitted by the bidder is enclosed as Annexure-V. In addition to Annexure-V, in case of other than Company/Proprietary firm, enclosed as Annexure-V A shall also be submitted by the each member of a Partnership Firm/ Joint Venture (JV)/ Hindu Undivided Family (HUF)/ Limited Liability Partnership (LLP) etc. as the case may be. Non submission of above certificate(s) by the bidder shall result in summarily rejection of his/their bid. It shall be mandatorily incumbent upon the tenderer to identify, state and submit the supporting documents duly self attested/digitally signed by which they/he is qualifying the Qualifying Criteria mentioned in the Tender Document. The format of Annexure V and Annexure VA are available at document section.

    Document required

  • The tenderer whether sole proprietor / a company or a partnership firm / joint venture (JV) / registered society / registered trust / HUF / LLP etc if they want to act through agent or individual partner(s), should submit along with the tender, a copy of power of attorney duly stamped and authenticated by a Notary Public or by Magistrate in favour of the specific person whether he/they be partner(s) of the firm or any other person, specifically authorizing him/them to sign the tender, submit the tender and further to deal with the Tender/ Contract up to the stage of signing the agreement except in case where such specific person is authorized for above purposes through a provision made in the partnership deed / Memorandum of Understanding / Article of Association /Board resolution, failing which tender shall be summarily rejected.

    Document required

  • A separate power of attorney duly stamped and authenticated by a Notary Public or by Magistrate in favour of the specific person whether he/they be partner(s) of the firm or any other person, shall be submitted after award of work, specifically authorizing him/them to deal with all other contractual activities subsequent to signing of agreement, if required.

    Document optional

  • The tenderer shall clearly specify whether the tender is submitted on his own (Proprietary Firm) or on behalf of a Partnership Firm / Company / Joint Venture (JV) / Registered Society / Registered Trust / Hindu Undivided Family (HUF) / Limited Liability Partnership (LLP) etc. The tenderer(s) shall enclose the attested copies of the constitution of their concern, and copy of PAN Card along with their tender. Tender Documents in such cases are to be signed by such persons as may be legally competent to sign them on behalf of the firm, company, association, trust or society, as the case may be. Following documents shall be submitted by the tenderer: -

    Document required

  • Following documents shall be submitted by the tenderer in case of Sole Proprietorship Firm: All documents in terms of Para 10 of the Tender Form (Second Sheet).

    Document required
Show all 19

  • Following documents shall be submitted by the tenderer in case of HUF:

    1. A copy of notarized affidavit on Stamp Paper declaring that he who is submitting the tender on behalf of HUF is in the position of 'Karta' of Hindu Undivided Family (HUF) and he has the authority, power and consent given by other members to act on behalf of HUF.
    2. All other documents in terms of Para 10 of the Tender Form (Second Sheet).
    Document required

  • Following documents shall be submitted by the tenderer in case of Company registered under Companies Act 2013:

    1. The copies of MOA (Memorandum of Association) / AOA (Articles of Association) of the company
    2. A copy of Certificate of Incorporation
    3. A copy of Authorization/Power of Attorney issued by the Company (backed by the resolution of Board of Directors) in favour of the individual to sign the tender on behalf of the company and create liability against the company.
    4. All other documents in terms Para 10 of the Tender Form (Second Sheet).
    Document required

  • Following documents shall be submitted by the tenderer in case of LLP (Limited Liability Partnership):

    1. A copy of LLP Agreement
    2. A copy of Certificate of Incorporation
    3. A copy of Power of Attorney/Authorization issued by the LLP in favour of the individual to sign the tender on behalf of the LLP and create liability against the LLP.
    4. An undertaking by all partners of the LLP that they are not blacklisted or debarred by Railways or any other Ministry / Department of the Govt. of India from participation in tenders / contracts as on the date of submission of bids, either in their individual capacity or in any firm/LLP or JV in which they were / are partners/members. Concealment / wrong information in regard to above shall make the contract liable for determination under Clause 62 of the Standard General Conditions of Contract.
    5. All other documents in terms of Para 10 of the Tender Form (Second Sheet). Following documents shall be submitted by the tenderer in case of Partnership Firm:
      1. A notarized copy of the Partnership Deed or a copy of the Partnership deed registered with the Registrar.
      2. A notarized or registered copy of Power of Attorney in favour of the individual to tender for the work, sign the agreement etc. and create liability against the firm.
      3. An undertaking by all partners of the partnership firm that they are not blacklisted or debarred by Railways or any other Ministry / Department of the Govt. of India from participation in tenders / contracts as on the date of submission of bids, either in their individual capacity or in any firm/LLP in which they were / are partners/members. Any Concealment / wrong information in regard to above shall make the bid ineligible or the contract shall be determined under Clause 62 of the Standard General Conditions of Contract.
      4. All other documents in terms of Para 10 of the Tender Form (Second Sheet).
    Document required

  • Following documents shall be submitted by the tenderer in case of Registered Society & Registered Trust:

    1. A copy of Certificate of Registration
    2. A copy of Memorandum of Association of Society/Trust Deed
    3. A copy of Power of Attorney in favour of the individual to sign the tender documents and create liability against the Society/Trust.
    4. A copy of Rules & Regulations of the Society
    5. All other documents in terms of Para 10 of the Tender Form (Second Sheet).
    Document required

  • The following documents should be specified for submission along with tender:

    Document optional

  • A list of personnel / organization on hand and proposed to be engaged for the tendered work.

    Document optional

  • A list of Plant & Machinery available on hand and proposed to be inducted and hired for the tendered work

    Document optional

  • List of Works completed in the last three financial years giving description of work, organization for whom executed, approximate value of contract at the time of award, date of award and date of scheduled completion of work, Date of actual start, actual completion and final value of contract should also be given.

    Document optional

  • List of works on hand indicating description of work, contract value, and approximate value of balance work yet to be done and date of award.

    Document optional

  • Letter of credit as mode of payment in works tenders or service tenders is available. It is an option for the contractor to take payment from Railways through a letter of credit (LC) arrangement. The details letter of credit as Annexure B is available at document section

    Document optional

  • Please submit bank details of the firm individual JV/partnership etc. i.e. name of the bank along with bank branch code, account number, IFSC code, PAN number and other necessary & relevant documents.

    Document required

  • All tenders for both supplies and works (including all service and maintenance contracts) having estimate value of Rs.10.00 Lakhs and above, an option for supplier/contractor to take payment from railway through a letter of credit (LC) arrangement. As per instruction of Railway Board's letter No.2018/CE-1/CT/9 dt. 04.06.2018 and FA & CAO/G/ECR's vide his letter No.ECR/Fin/Exp/LC dated 16.05.2018, a format (Annexure-B) is attached herewith for documents

    Document optional

  • The tenderers in their bids shall indicate the details of their Jurisdictional Assessing Officers (Designation, address & email Id). In case of a contract award, a copy of the LOA/Purchase Order shall be immediately forwarded by Purchaser to the Jurisdictional Assessing Officer mentioned in the Tenderer's bid.

    Document required

Eligibility

Standard Financial Criteria

  • The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees. N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet. Note: "The balance sheet and all other financial documents attested/certified by the Chartered Accountant (CA) to substantiate fulfillment of Financial Eligibility Criteria should be with UDIN, failing which the offer shall be considered as incomplete and will be summarily rejected without any further reference".

    Document required

Standard Technical Criteria

  • The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited:

    1. Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or
    2. Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or
    3. One similar work costing not less than the amount equal to 60% of advertised value of the tender.
    Document required

  • Work experience certificate from private individual shall not be considered. However, in addition to work experience certificates issued by any Govt. Organisation, work experience certificate issued by Public listed company having average annual turnover of Rs 500 crore and above in last 3 financial years excluding the current financial year, listed on National Stock Exchange or Bombay Stock Exchange, incorporated/registered at least 5 years prior to the date of closing of tender, shall also be considered provided the work experience certificate has been issued by a person authorized by the Public listed company to issue such certificates. In case tenderer submits work experience certificate issued by public listed company, the tenderer shall also submit along with work experience certificate, the relevant copy of work order, bill of quantities, bill wise details of payment received duly certified by Chartered Accountant, TDS certificates for all payments received and copy of final/last bill paid by company in support of above work experience certificate.

  • Defination of Similar Work Any Civil engineering work involving fabrication, assembling, erection & launching open web girder/plate girder/ composite girder or Any Civil engineering work involving assembling, erection & launching / re-girdering of open web girder/plate girder/ composite girder o r Any Civil engineering work involving fabrication, assembling, erection & launching of FOB/Light ROB/PEB steel structures or Any Civil engineering work involving assembling, erection & launching of FOB/Light ROB/PEB steel structures

Partnership firm/Joint Venture (JV) / Hindu Undivided Family (HUF) / Limited Liability Partnership (LLP) etc.

  • Please submit a certificate in the prescribed format (please download the format from the link given below). Non submission of the certificate, or submission of certificate either not properly filled in, or in a format other than the prescribed format shall lead to summary rejection of your offer. ( Click here to download the Format of Self Certification)

Check each criterion against the tender notice before you bid.

Commercial conditions

EMD
₹1,097,700
Tender fee
None

Terms & conditions

10 conditions

Commercial-Compliance

  • The Railway reserves the right to verify all statements, information and documents submitted by the bidder in his tender offer, and the bidder shall, when so required by the Railway, make available all such information, evidence and documents as may be necessary for such verification. Any such verification or lack of such verification, by the Railway shall not relieve the bidder of its obligations or liabilities hereunder nor will it affect any rights of the Railway there under

  • In case of any information submitted by tenderer is found to be false, forged or incorrect at any time during process for evaluation of tenders, it shall lead to forfeiture of the tender Bid Security besides banning of business for a period of upto two years.

  • In case of any information submitted by tenderer is found to be false, forged or incorrect after the award of contract, the contract shall be terminated. Bid Security, Performance Guarantee and Security Deposit available with the railway shall be forfeited. In addition, other dues of the contractor, if any, under this contract shall be forfeited and agency shall be banned for doing business for a period of upto two years.

  • Non-compliance with any of the conditions set forth therein above is liable to result in the tender being rejected.

General Instructions

  • Special criteria for evaluation if there is sub-sectioning (Railway Board letter no. 2001/CEI/CT/3 dated 12.04.2001). (Railway Board letter no. 2018/CE- I/CT/AP/2 dated 17.04.2016)

    1. If sub- sectioning has been done with a view to expedite the work then, only one tender will be awarded to one firm.
    2. If the same firm becomes L-1 in all the sub-section, then evaluation of the firm for its fitness for award of all or a few tenders should be done for the tender as a whole/under consideration. This is with a view to avoid overloading of the firms beyond their financial capability

  • In case of more than one L-1 bidders, tender may be awarded to tenderer having higher Bid Capacity. In case Bid Capacity is also the same tenderer having done more value of similar work in last three previous financial years and the current financial year upto the date of opening of the tender, may be selected for the award instructions with respect to Bid Capacity will follow.

  • For those conditions for which standard formats have been given in the uploaded document titled-Formats for uploading of various format. The information should only be submitted in these standard formats.

  • Rates are inclusive of all taxes/octroi, license fee, royalty charges etc. legally leviable by State, Central Govt. and/or any other local authority.

  • The tenderer shall be required to submit the Bid Security with the tender for the due performance with the stipulation to keep the offer open till such date as specified in the tender, under the conditions of tender.

  • BOOKS OF REFERENCE These tender documents are to be read with the followings books with versions updated/corrected/modified up to the date of tender opening:

    1. Standard General Conditions of Contract April 2022 as amended by updated correction slips termed GCC 2022.
    2. DSR-2021 as amended by updated correction slips.
    3. E. C. Railway Engineering department unified standard schedule or rates 2021 as amended by updated correction slips (termed USSOR, 2021) up to the date of tender opening.
    4. CENTRAL PUBLIC WORKS DEPARTMENT specifications contained in VOLUME-I and VOLUME-II, with updated corrections slips. These four books are where-inafter called the "Books of reference" and shall govern this tender as well as the contract resulting from the acceptance from this tender, to the extent that these contents do not conflict with the contains of the various chapters of these documents.
Bidder declarations (16)

Undertakings

  • I/ We have visited the works site and I / We am / are aware of the site conditions.

  • Before submitting a tender, the tenderer will be deemed to have satisfied himself by actual inspection of the site and locality of the works, that all conditions liable to be encountered during the execution of the works are taken into account and that the rates he enters in the tender forms are adequate and all inclusive to accord with the provisions in Clause-37 of the Standard General Conditions of Contract for the completion of works to the entire satisfaction of the Engineer.

  • Tenderers will examine the various provisions of The Central Goods and Services Tax Act, 2017(CGST)/ Integrated Goods and Services Tax Act, 2017(IGST)/ Union Territory Goods and Services Tax Act, 2017(UTGST)/ respective state's State Goods and Services Tax Act (SGST) also, as notified by Central/State Govt.& as amended from time to time and applicable taxes before bidding. Tenderers will ensure that full benefit of Input Tax Credit (ITC) likely to be availed by them is duly considered while quoting rates.

  • The successful tenderer who is liable to be registered under CGST/IGST/UTGST/SGST Act shall submit GSTIN along with other details required under CGST/IGST/UTGST/SGST Act to railway immediately after the award of contract, without which no payment shall be released to the Contractor. The Contractor shall be responsible for deposition of applicable GST to the concerned authority.

  • In case the successful tenderer is not liable to be registered under CGST/IGST/UTGST/ SGST Act, the railway shall deduct the applicable GST from his/their bills under reverse charge mechanism (RCM) and deposit the same to the concerned authority.

  • When work is tendered for by a firm or company, the tender shall be signed by the individual legally authorized to enter into commitments on their behalf. The Railway will not be bound by any power of attorney granted by the tenderer or by changes in the composition of the firm made subsequent to the execution of the contract. It may, however, recognize such power of attorney and changes after obtaining proper legal advice, the cost of which will be chargeable to the Contractor.

Certifications

  • I/we the tenderer (s) am/are signing this document after carefully reading the contents.

  • I/We the tenderer(s) also accept all the conditions of the tender and have signed all the pages in confirmation thereof.

  • I/we hereby declare that I/we have downloaded the tender documents from Indian Railway website www.ireps.gov.in . I/we have verified the content of the document from the website and there is no addition, no deletion or no alteration to the content of the tender document. In case of any discrepancy noticed at any stage i.e. evaluation of tenders, execution of work or final payment of the contract, the master copy available with the railway Administration shall be final and binding upon me/us.

  • I/we declare and certify that I/we have not made any misleading or false representation in the forms, statements and attachments in proof of the qualification requirements.

  • I/We also understand that my/our offer will be evaluated based on the documents/credentials submitted along with the offer and same shall be binding upon me/us.

  • I/We declare that the information and documents submitted along with the tender by me/us are correct and I/we are fully responsible for the correctness of the information and documents, submitted by us.

  • I/we certify that I/we the tenderer(s) is/are not blacklisted or debarred by Railways or any other Ministry / Department of Govt. of India from participation in tender on the date of submission of bids, either in individual capacity or as a HUF/ member of the partnership firm/LLP/JV/Society/Trust.

  • I/we understand that if the contents of the certificate submitted by us are found to be forged/false at any time during process for evaluation of tenders, it shall lead to forfeiture of the Bid Security and may also lead to any other action provided in the contract including banning of business for a period of upto two year. Further, I/we and all my/our constituents understand that my/our offer shall be summarily rejected.

  • I/we also understand that if the contents of the certificate submitted by us are found to be false/forged at any time after the award of the contract, it will lead to termination of the contract, along with forfeiture of Bid Security/Security Deposit and Performance guarantee and may also lead to any other action provided in the contract including banning of business for a period of upto two year.

  • I/We have read the clause regarding restriction on procurement from a bidder of a country which shares a land border with India and certify that I am/We are not from such a country or, if from such a country, have been registered with the competent Authority. I/We hereby certify that I/we fulfil all the requirements in this regard and am/are eligible to be considered (evidence of valid registration by the competent authority is enclosed)

Similar open tenders

Soonest first

Search similar in the explorerFind this tender in the explorer

Tender notice (PDF)